NAS Firmware Update When No HDD(s) Installed

From QNAPedia
Jump to navigation Jump to search

NOTE:

  1. This procedures are used to update the flash / DOM (disk on module) firmware on the NAS.
  2. Make sure no HDD installed before update.
  3. Flash image are required for NAS with 16MB flash or 128MB DOM.
  4. For NAS with 512MB DOM, just use the firmware on QNAP download site (http://www.qnap.com/download.asp).
  5. This updated procedures are generally used when the NAS can be found by QNAP Finder but cannot be initialized with HDD(s).
  6. QNAP NAS also store firmware on the HDDs. If you have initialized the NAS with HDDs before, this update procedures will cause the firmware version mismatch between the NAS and the HDDs. You need to update the firmware again after boot up with HDDs installed.


Download link of the flash image:

HS-210
http://eu1.qnap.com/Storage/tsd/flashimage/HS-210_20140612-4.1.0.Flash.img

TS-110
http://us1.qnap.com/Storage/tsd/flashimage/TS-110_20140612-4.1.0.Flash.img

TS-112, TS-112P
http://us1.qnap.com/Storage/tsd/flashimage/TS-112_20140612-4.1.0.Flash.img

TS-119, TS-119P+, TS-119PII
http://us1.qnap.com/Storage/tsd/flashimage/TS-119_20140612-4.1.0.Flash.img

TS-120
http://us1.qnap.com/Storage/tsd/flashimage/TS-120_20140612-4.1.0.Flash.img

TS-121
http://us1.qnap.com/Storage/tsd/flashimage/TS-121_20140612-4.1.0.Flash.img

TS-210
http://us1.qnap.com/Storage/tsd/flashimage/TS-210_20140612-4.1.0.Flash.img

TS-212, TS-212P, TS-212-E 
http://us1.qnap.com/Storage/tsd/flashimage/TS-212_20140612-4.1.0.Flash.img

TS-219, TS-219P, TS-219P+, TS-219PII
http://us1.qnap.com/Storage/tsd/flashimage/TS-219_20140612-4.1.0.Flash.img

TS-220
http://us1.qnap.com/Storage/tsd/flashimage/TS-220_20140612-4.1.0.Flash.img

TS-221
http://us1.qnap.com/Storage/tsd/flashimage/TS-221_20140612-4.1.0.Flash.img

TS-410
http://us1.qnap.com/Storage/tsd/flashimage/TS-410_20140612-4.1.0.Flash.img

TS-410U
http://us1.qnap.com/Storage/tsd/flashimage/TS-410U_20140612-4.1.0.Flash.img

TS-412
http://us1.qnap.com/Storage/tsd/flashimage/TS-412_20140612-4.1.0.Flash.img

TS-412U
http://us1.qnap.com/Storage/tsd/flashimage/TS-412U_20140612-4.1.0.Flash.img

TS-419P, TS-419P+, TS-419PII
http://us1.qnap.com/Storage/tsd/flashimage/TS-419P_20140612-4.1.0.Flash.img

TS-419U, TS-419U+, TS-419UII
http://us1.qnap.com/Storage/tsd/flashimage/TS-419U_20140612-4.1.0.Flash.img

TS-420
http://us1.qnap.com/Storage/tsd/flashimage/TS-420_20140612-4.1.0.Flash.img

TS-420U
http://us1.qnap.com/Storage/tsd/flashimage/TS-420U_20140612-4.1.0.Flash.img

TS-421
http://us1.qnap.com/Storage/tsd/flashimage/TS-421_20140612-4.1.0.Flash.img

TS-421U
http://us1.qnap.com/Storage/tsd/flashimage/TS-421U_20140612-4.1.0.Flash.img

TS-239
http://us1.qnap.com/Storage/tsd/flashimage/TS-239_20120801-3.7.3.Flash.img

TS-439
http://us1.qnap.com/Storage/tsd/flashimage/TS-439_20120801-3.7.3.Flash.img

TS-439U
http://us1.qnap.com/Storage/tsd/flashimage/TS-439U_20120801-3.7.3.Flash.img

TS-639
http://us1.qnap.com/Storage/tsd/flashimage/TS-639_20120801-3.7.3.Flash.img

TS-509
http://us1.qnap.com/Storage/tsd/flashimage/TS-509_20120801-3.7.3.Flash.img

TS-809
http://us1.qnap.com/Storage/tsd/flashimage/TS-809_20120801-3.7.3.Flash.img

TS-809U
http://us1.qnap.com/Storage/tsd/flashimage/TS-809U_20120801-3.7.3.Flash.img

SS-439
http://us1.qnap.com/Storage/tsd/flashimage/SS-439_20120801-3.7.3.Flash.img

SS-839
http://us1.qnap.com/Storage/tsd/flashimage/SS-839_20120801-3.7.3.Flash.img


Update Procedures:

  1. Power off the NAS
  2. Remove all the HDDs
  3. Power on the NAS
  4. After a short beep and a long beep(about two minutes after first short beep), run the QNAP Finder(Make sure the Finder is the latest version).
  5. QNAP Finder should find the NAS and its IP
  6. Select the NAS and click “Tools” -> “Update Firmware”
  7. Input default username and password (admin/admin)
  8. Select the image files on your PC for the NAS.
  9. After firmware update, the NAS will be reboot.
  10. Make sure the firmware have been updated
  11. Power off the NAS
  12. Plug all the HDD back
  13. After power on, follow the messages on the Finder to initialize the NAS.